Replacing uPVC Window Handles
It is simple to change the handles on windows made of Upvc. It is crucial to ensure that the new handle fits inside the spindle cutout of the window mechanism.
If the steps below are followed, any cockspur handle should fit most windows. The most important thing is the step height of the handle.
What to Find
A large portion of windows in the UK are fitted with uPVC handles, and over time they can begin to show signs of wear and tear. The handle on the window can become loose or difficult-to-operate when this happens. This is a easy task that can be accomplished by anyone who is comfortable using basic hand tools.
The first thing to do is make sure the handle is securely attached to the window frame and is in the open position. The next step is to find the fixing screws or pins that hold the handle in position. They are usually located on the inside face of the handle and can be removed with a screwdriver or pliers.
When the handle has become loose and sagging, gently pull it back from its hinges. It is then necessary to locate a replacement handle of the same style and size. This can be done in the DIY store or on the internet. The process should take only five minutes and requires a screwdriver is all you need.
When replacing repairmywindowsanddoors.co.uk of a uPVC handle, it is important to think about the step height. This is the distance from the base of the handle until it sits on the frame of the window. This is a typical measurement and you should check the step height before ordering the replacement handle.
There are various sizes depending on the type of handle. Inline handles for uPVC windows usually feature lug centers of 31mm There are also cockspur handle types with 43mm centres. Tilt-and-turn handles are common on uPVC Windows. They have a special design which allows the window be tilted to allow for ventilation, and then turned to fully open the window.
The most common uPVC handle breakage is internal cracking, rather than a fracture from the base. This can make it difficult to open. It is essential to ensure that the replacement handle has the same spindle that was used in your original one.
Remove the old Handle
A poorly fitted or damaged window handles may cause your double-glazed windows to open and close incorrectly, and can result in them becoming stuck. There are many reasons including general wear and tear, or corrosion of the handle. In these cases it is essential to locate replacement window handles made of upvc as soon as possible to prevent further damage and loss of function.
One of the first things to do when replacing upvc window handles is to remove the old handle from the window. To do this, begin by taking off the screw that is covered when the handle is in the closed position. After you have removed the screw, you are able to remove the handle. It is a good idea to employ an electric screwdriver to accomplish this as it will make the task much easier and quicker.
It is also important to note that the handles' screws could be hidden behind plastic caps, therefore it is a good idea to use a Stanley knife to the screw covers and remove them. After the handle has been removed, you must examine the square cut out on the base of the handle to make sure that the new window lock handles are compatible with it. It is crucial to measure the spindle length on the handle that was used and then compare it with the size of the window mechanism spindle cutout.
The various types of upvc window handles are: Espag handles, which have a central screw and can turn left or right; Cranked handles, which have two screws and are used on tilt and turn windows made of upvc as well as Spade handles, with an arm that is flat and can be put on either side of the window. Once you have found a suitable replacement, it's simple to screw the handle in place and ensuring that the spindle is correctly placed into the lock mechanism. After that, you can then tighten the handle to the window frame. The replacement upvc handle should now be secure.
Take a look at the Spindle
If you're replacing a upvc window handle that has slipped off, it's likely because the spindle holding it in place has become loose or damaged. In some cases, you can tighten the spindle by using pins or screws. In some instances it is necessary to replace the handle. There are several different types of handles made of upvc. These include inline espagnolette handles as well as cockspur handles. tilt and turn handles. Each type has a different method for installing and replacing the handle.
It is important to measure the current handle before purchasing an alternative. This will ensure that the handle will fit the window in a proper manner and will be of the correct size. All handles are sized in accordance with industry standards, making it easy to identify the correct size.
To determine the size of your handle, first remove it from the window by turning it back to the open position. You should be able see the size of the pin or screw that holds the handle. Then, use a tape measure or ruler to determine the length of the spindle. Once you have determined the length of the spindle you can buy a new one that is exactly the same size.
When buying a replacement, it is important to take into consideration the step height of a window handle made of upvc. The step height is measured from the base to the point at which the handle is positioned on the frame. In general, this is approximately 21mm for uPVC windows and 9mm for aluminum. Dropping objects into the gap will allow you to observe how far the handle extends before it meets an obstruction.
Cockspur handles can have different backsets, based on the type of window you put them in. Inline espag handles have an average height of 43mm centre to centre (2 fixing points). Cockspur handles however, have different backset heights depending on the style of the window they're in. This is because they have a spur that extends from the handle and locks over a cockspur wedge striker.
Fit the New Handle
If you've decided to replace the handle, carefully align it with the screw holes on the door and fix it using the screws provided. Install the latch lever in similar fashion to the main handle when you're replacing the door handle. Then, you can reattach the door trim to conceal the mounting screws and close the project.
Tips: To remove the metal head from the wedge of wood make sure the handle is held so that its longer end is resting on the floor and use a hammer to tap the thin end of the handle. Be careful not to scratch the handle or handle spindle.